Full Demo and Haul-Away
We remove the old surround, doors, and any failed backer board, then haul it all away. You do not rent a dumpster or make a trip to the landfill. Demo and cleanup are part of the price.
Waterproof, code-correct surrounds built for Idaho homes
Shower Enclosure and Surround Installation pocatello ID
When you need shower enclosure and surround installation pocatello ID homeowners trust, we tear out the failing walls, fix the waterproofing, and set a new surround that stays dry for decades. From acrylic panels to tile and glass, our crew handles shower surround installation in pocatello for tub-to-shower conversions, leaky stalls, and full bathroom remodels. Same-week estimates, clean job sites, and work that passes inspection.
Careful work. Honest options.
About this service
Shower Enclosure and Surround Installation pocatello ID
Shower enclosure and surround installation pocatello ID is the trade of removing old shower walls, repairing or replacing the pan and drain, installing waterproof backer and membrane, then setting a new surround and enclosure that seals water inside the stall. We work with acrylic panels, ceramic and porcelain tile, natural stone, and glass mosaic, plus glass doors from DreamLine, Vigo, and Sterling. Every job starts with the drain, the valve, and the slope, because a pretty surround over a bad pan will leak within a year.
Pocatello homes take a beating from hard water and cold snaps that crack old caulk and grout. In Bannock County, we see plenty of 1970s and 1980s tub surrounds with failed caulking, mold behind the cement backer board, and shower doors that no longer close because the base has shifted. If you have been searching for shower surround near me pocatello, the fix is rarely just new panels. It is a full rebuild of the wet layer, done with the right membrane and a properly sloped pan.
- ✓ Stops Hidden Water Damage
- ✓ Ends the Mold Cycle
- ✓ Fits Tub-to-Shower Conversions
- ✓ Raises Home Value
What's included
What Our Shower Surround Installation Includes
Every shower enclosure and surround installation we do covers the full wet layer, not just the visible surface. Here is what is included in a standard Pocatello install, and what we quote separately when your shower needs more than a surface swap.
Waterproofing and Backer Board
We install cement backer board and a waterproofing membrane at every seam, corner, and curb. This is the layer that keeps water out of your framing and the reason the surround lasts.
Surround and Tile Setting
Acrylic panels or tile go up level and tight, set with thinset mortar and finished with grout and silicone caulk. We keep the joints consistent and the edges trimmed clean.
Glass Enclosure or Door
We hang and adjust your shower door or enclosure, check the swing and seal, and run a water test. Frameless and framed options are both available from DreamLine, Vigo, and Sterling.
Plumbing Connections
A licensed plumber handles the shower valve and drain connections, tests them, and signs off before the walls close. That keeps the install code-correct and protects your home.
Final Water Test and Walkthrough
Before we leave, we run water through the shower, check for leaks at the pan, drain, and seams, and walk you through care instructions and warranty paperwork.
How it works
How Our Installation Process Works
We measure the stall, check the pan slope with a level, test the shower valve and drain, and look for soft spots in the wall. You get a written price the same day, not a range that grows later. If the pan or valve is failing, we tell you up front so there are no surprises mid-job.
We pull the old surround, doors, and any rotten backer board. With the wall open we inspect the framing, the shower pan liner, and the drain connection. This is where we find the cracked pans and clogged drains that caused the original leak. Demo usually takes two to four hours.
We replace the shower valve, drain, and pan liner as needed, then install cement backer board and roll on a waterproofing membrane at the seams, corners, and curb. A licensed plumber handles the valve and drain work. This stage is the one that determines whether the shower lasts.
We set your acrylic panels or tile with thinset mortar, grout float, and notched trowel, keeping every course level and every joint tight. Then we hang the glass enclosure or door, check the swing and seal, and run a full water test before we call it done.
We haul away the old surround and debris, wipe down the new surfaces, and walk you through the finished shower. You get care instructions for the caulk and grout, plus our warranty paperwork. The job site is left broom-clean, same as we found it.
STEP 01On-Site Assessment
We measure the stall, check the pan slope with a level, test the shower valve and drain, and look for soft spots in the wall. You get a written price the same day, not a range that grows later. If the pan or valve is failing, we tell you up front so there are no surprises mid-job.
Tools & methods
Tools and Methods We Use
Wet Saw and Tile Saw
Used to cut porcelain, ceramic, and natural stone tile cleanly, including around the valve, niche, and drain. Precise cuts mean tight joints and no chipped edges on your surround.
Notched Trowel and Grout Float
The notched trowel spreads thinset mortar at the correct depth for full tile coverage. The grout float packs grout into the joints evenly, so the finish is consistent and water-resistant.
Caulking Gun and Silicone Caulk
We seal the seams, corners, and curb with silicone caulk rated for wet areas. A steady caulk line is the last line of defense against water reaching the framing.
Level and Measuring Tape
Level checks keep the pan, curb, and surround square and plumb. A surround that is out of level will not seal, and a glass door hung on it will not close right.
Pipe Wrench and Drain Wrench
Our plumber uses these to set the shower valve and tighten the drain connection. A properly torqued drain is what keeps the pan from leaking into the ceiling below.
Drill and Screwdriver Set
Used to fasten backer board, set blocking for grab bars and seats, and mount enclosure hardware. Solid fastening is what keeps the surround and door stable for years.
Real results
Before and after.
Shower Enclosure and Surround Installation
Old Town Tub Surround Rebuild
A 1978 tub surround with cracked grout, black mold along the caulk line, and soft drywall behind the tile. The homeowner had recaulked it three times in five years and the musty smell kept coming back.
After: We removed the surround and backer board, treated the framing, and rebuilt with cement backer board and a waterproofing membrane. New porcelain tile, a Moen valve, and a framed glass door went in over four days. The moisture meter reads dry after six months of daily use.
Book this service →
Shower Enclosure and Surround Installation
Highland Tub-to-Shower Conversion
A standard tub in a 1990s Highland home that the owners could no longer step over. The existing surround was acrylic over drywall, with no waterproofing and a drain that pooled water at the low corner.
After: We pulled the tub, relocated the drain, set a new walk-in pan, and built a tiled surround with a low threshold. A frameless DreamLine door finished the job. The pan now drains fully in under 30 seconds with no standing water.
Book this service →
Shower Enclosure and Surround Installation
Cedar Hills Accessible Shower Upgrade
An original 1985 acrylic surround with no wall blocking, so grab bars could only be mounted with toggle bolts that pulled loose. The homeowner's mother had stopped using the shower because she did not feel safe.
After: We rebuilt the surround with blocking at ADA compliance heights, installed a fold-down seat and two grab bars, and replaced the valve with a Hansgrohe pressure-balance unit. The bars now hold 250 pounds with no flex.
Book this service → Problems we solve
Shower Problems We Fix for Pocatello Homes
Most surrounds we replace were installed over a failing wet layer. Here are the problems Pocatello homeowners call us about, and how we solve them for good instead of patching over the symptom.
Ask a pro →Shower leaks staining the ceiling below
We trace the leak to the pan liner, drain, or surround seam, repair the source, and rebuild the wet layer with new waterproofing. The surround goes back up over a sealed, tested assembly, so the leak does not return.
Mold and mildew behind the tile
We cut out the contaminated backer board, treat the framing, and rebuild with mold-resistant materials and a waterproofing membrane. The new surround dries out between uses instead of holding moisture.
Failed caulking and grout lines
We remove the old caulk and grout, dry the joints, and reseal with silicone caulk rated for wet areas. If the failure is widespread, we rebuild the surround so you are not resealing it every year.
Shower door not closing or sealing
We find the cause, whether it is an uneven shower base or a surround that is out of plumb, fix it, and rehang or replace the door. The enclosure seals again and the floor stays dry.
Transparent pricing
Shower Surround Installation Cost
$1,800 - $6,500 depending on scope
Typical 2026 pricing for shower enclosure and surround installation in Pocatello runs $1,800 to $6,500 depending on material, size, and how much plumbing needs replacing. Acrylic panels over a sound pan sit at the low end. Tile with new waterproofing, a replaced valve, and a glass enclosure push toward the top. We quote the full scope in writing after measuring your stall, so the number does not move once work starts. If you want affordable shower surround installation pocatello Idaho without cutting the waterproofing, we will show you where the money goes and where it does not need to.
The waterproofing and plumbing work is what makes a surround last. Spending on the wet layer now avoids a $9,000 structural repair later. We quote the full scope in writing so you can compare real numbers, not lowball guesses.
•affects cost
Acrylic panels cost less and install faster. Porcelain or ceramic tile costs more in material and labor but lasts longer and can be repaired in sections. Natural stone is the premium option and needs annual sealing.
Get a quote ↗•affects cost
A standard 32 by 60 inch stall is straightforward. Larger walk-ins, corner units, and neo-angle layouts take more material and more cutting, which raises the price.
Get a quote ↗•affects cost
If the valve, drain, or pan liner is failing, replacing them adds cost. We find this during demo, and we tell you before we proceed rather than surprising you at the end.
Get a quote ↗•affects cost
A full membrane system at the seams, corners, and curb costs more than a surface-only install, but it is what prevents the rot and mold that lead to a full rebuild later.
Get a quote ↗ Proof you can check
Licensed, Insured, and Warrantied
- Licensed Contractor · State of Idaho
- Licensed Plumber · State of Idaho
- ICC Code Compliance · International Code Council
- EPA WaterSense Partner · U.S. Environmental Protection Agency
- Manufacturer Certified Installer · Schluter Systems and Laticrete
Most shower surround installations in Pocatello run $1,800 to $6,500 in 2026, depending on material and scope. Acrylic panels over a sound pan sit at the low end. Tile with new waterproofing, a replaced valve, and a glass enclosure push toward the top. If the pan or framing is rotted, add $800 to $2,500 for the repair. We quote the full scope in writing so the number does not move.
For most Pocatello homes, porcelain tile over a Schluter Systems waterproofing membrane is the best long-term choice, because it handles hard water and cold snaps and can be repaired in sections. Acrylic panels are the affordable pick when budget matters and the walls are sound. Natural stone looks great but needs sealing every year. We match the material to your pan, valve, and how you actually use the shower.
A standard surround swap takes one to two days. A full tear-out with new backer board, waterproofing, tile, and a glass enclosure runs three to five days, mostly because of cure time for thinset and grout. We schedule the water test and final caulk on the last day. You will know the timeline before we start, and we keep the bathroom usable as long as possible.
We do. ShowerPro Installation handles shower enclosure and surround installation across Pocatello and Bannock County, including Downtown, Old Town, Highland, Alameda, and the Idaho State University District. Call +1 986-336-9120 and we will set a same-week estimate. We bring samples, measure your stall, and give you a written price before any work begins.
Ready when you are
Get Your Shower Enclosure and Surround Installation pocatello ID Quote
We give written pricing, show up on schedule, and waterproof every surround like it is going in our own house. Call ShowerPro Installation at +1 986-336-9120 for a same-week estimate on your Pocatello shower.
Get Free Estimate +19863369120 →
Request an appointment
get your free shower estimate
Call us at +1 986-336-9120 or email [email protected] and we'll set up a free on-site measure. We answer the phone Monday through Friday, 8:00 to 18:00, and we return every message the same business day. For a leaking shower or a valve that's spraying, call any time - we run emergency call-outs 24/7.